《案例精解企业级网络构建》赠书活动开始啦！　最新活动：“Web安全大家谈”有奖征文

在路由器上使用IPV6（上）－－在NBMA中使用IPV6

2007-02-08 22:05:42

　标签：路由路由器 IPv6 在路由器上使用IPV6　　　[推送到技术圈]

R1, R2, R3的S2/0端口通过FRAME-RELAY交换机连接。

R1

conf t

ipv6 unicast-routing

int l0

ipv6 address fec0:0:0:1::1/64

exit

int s2/0

ipv6 address fec0:0:0:123::1/64

encap frame

no arp frame

no frame inver

frame map ipv6 fec0:0:0:123::2 102 b

frame map ipv6 fec0:0:0:123::3 103 b

no shut

end

R2

conf t

ipv6 unicast-routing

int l0

ipv6 address fec0:0:0:2::2/64

int s2/0

ipv6 address fec0:0:0:123::2/64

encap frame

no arp f

no frame inver

frame map ipv6 fec0:0:0:123::1 201 b

frame map ipv6 fec0:0:0:123::3 201 b

no shut

end

R3

conf t

ipv6 unicast-routing

int l 0

ipv6 address fec0:0:0:3::3/64

int s2/0

ipv6 address fec0:0:0:123::3/64

encap frame

no arp f

no frame inver

frame map ipv6 fec0:0:0:123::1 301 b

frame map ipv6 fec0:0:0:123::2 301 b

no shut

end

R1#sh ipv6 int s 2/0 | include link-local
IPv6 is enabled, link-local address is FE80::C800:8FF:FE90:0

R2#sh ipv6 int s 2/0 | include link-local
IPv6 is enabled, link-local address is FE80::C800:DFF:FE44:0

R3#sh ipv6 int s 2/0 | include link-local
IPv6 is enabled, link-local address is FE80::C800:AFF:FE80:0

R1

conf t

int s 2//0

frame-relay map ipv6 FE80::C800:AFF:FE80:0 103 broadcast
frame-relay map ipv6 FE80::C800:DFF:FE44:0 102 broadcast

R2

conf t

int s 2/0

frame-relay map ipv6 FE80::C800:AFF:FE80:0 201 broadcast
frame-relay map ipv6 FE80::C800:8FF:FE90:0 201 broadcast

R3

conf t

int s 2/0

frame-relay map ipv6 FE80::C800:DFF:FE44:0 301 broadcast
frame-relay map ipv6 FE80::C800:8FF:FE90:0 301 broadcast

校验

R1#sh frame map
Serial2/0 (up): ipv6 FE80::C800:AFF:FE80:0 dlci 103(0x67,0x1870), static,
              broadcast,
              CISCO, status defined, active
Serial2/0 (up): ipv6 FE80::C800:DFF:FE44:0 dlci 102(0x66,0x1860), static,
              broadcast,
              CISCO, status defined, active
Serial2/0 (up): ipv6 FEC0:0:0:123::2 dlci 102(0x66,0x1860), static,
              broadcast,
              CISCO, status defined, active
Serial2/0 (up): ipv6 FEC0:0:0:123::3 dlci 103(0x67,0x1870), static,
              broadcast,
              CISCO, status defined, active

R2#sh frame map
Serial2/0 (up): ipv6 FE80::C800:AFF:FE80:0 dlci 201(0xC9,0x3090), static,
              broadcast,
              CISCO, status defined, active
Serial2/0 (up): ipv6 FE80::C800:8FF:FE90:0 dlci 201(0xC9,0x3090), static,
              broadcast,
              CISCO, status defined, active
Serial2/0 (up): ipv6 FEC0:0:0:123::1 dlci 201(0xC9,0x3090), static,
              broadcast,
              CISCO, status defined, active
Serial2/0 (up): ipv6 FEC0:0:0:123::3 dlci 201(0xC9,0x3090), static,
              broadcast,
              CISCO, status defined, active

R3#sh frame map
Serial2/0 (up): ipv6 FE80::C800:DFF:FE44:0 dlci 301(0x12D,0x48D0), static,
              broadcast,
              CISCO, status defined, active
Serial2/0 (up): ipv6 FE80::C800:8FF:FE90:0 dlci 301(0x12D,0x48D0), static,
              broadcast,
              CISCO, status defined, active
Serial2/0 (up): ipv6 FEC0:0:0:123::1 dlci 301(0x12D,0x48D0), static,
              broadcast,
              CISCO, status defined, active
Serial2/0 (up): ipv6 FEC0:0:0:123::2 dlci 301(0x12D,0x48D0), static,
              broadcast,
              CISCO, status defined, active

R1#ping fec0:0:0:123::2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:0:0:123::2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 12/44/68 ms
R1#ping fec0:0:0:123::3

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:0:0:123::3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/41/108 ms

R2#ping fec0:0:0:123::1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:0:0:123::1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 12/62/160 ms
R2#ping fec0:0:0:123::3

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:0:0:123::3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 24/67/120 ms

R3#ping fec0:0:0:123::1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:0:0:123::1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/48/108 ms
R3#ping fec0:0:0:123::2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:0:0:123::2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 16/47/140 ms

本文出自 “穿过地狱去看海” 博客，谢绝转载！

上一篇在路由器上配置NAT(Network Address Translation)　　下一篇在路由器上使用IPV6（中）－－RIP和OSPF的应用

类别：CCIE ┆ 技术圈() ┆ 阅读() ┆ 评论() ┆推送到技术圈 ┆返回首页

相关文章

文章评论

7layer

2007-02-08 22:20:16

支持一下 .学习一下

[匿名]一边

2007-03-01 01:34:40

IPV6好难，，，

昵称：
验证码：		点击图片可刷新验证码　　博客过2级，无需填写验证码
内容：